It is especially useful for repairing dead boot issues through ISP or BROM (Preloader) mode.

📱 Device Specifications:

• Model Name: Realme C61

• Model Number: RMX3930

• Chipset (CPU): Unisoc T612 (Spreadtrum)

• Storage Type: eMMC

• Boot Mode: Preloader / BROM Mode

• Dump Format: Scatter Partition File

• Tool Used: UnlockTool

• Status: Fully Tested & Verified

🔧 Use Case Scenarios:

• Device is completely dead or not turning on

• Stuck on Realme logo, bootloop, or fastboot mode

• Partition damage after a wrong firmware flash

• EMMC or ROM level repair using ISP pinout

• Fixing partitions like preloader, nvram, lk, system, and userdata

⚠️ Important Note Before Flashing:

Always backup security partitions such as NVRAM, NVDATA, and IMEI before flashing.
If these are lost, the device may face IMEI loss, baseband unknown, or no network issues.

✅ Flashing Instructions:

1. Extract the dump file on your computer.

2. Open UnlockTool and go to the Unisoc section.

3. Load the Unisoc scatter file from the dump folder.

4. Connect the device in Preloader/BROM mode (usually Volume Down + USB) or via ISP method.

5. Select and flash required partitions or full dump as needed.

6. Once flashed, disconnect and power on the phone.

Optional: After dump flashing, you can install full stock firmware for complete software recovery and stability.

📥 Download Link:

🔗 Realme C61 (RMX3930) Scatter Dump File – Free Download (TechFixForum)

or ISP-based methods.

📱 Device Information:

• Model Name: Realme 8i

• Model Number: RMX3151

• Chipset (CPU): MediaTek Helio G96 (MT6781)

• Storage Type: eMMC

• Boot Mode: Preloader / BROM Mode

• Dump Tool Used: Pandora Box

• File Type: Scatter Dump Format

• Status: 100% Tested & Verified

🔧 Use This Dump File If:

• Your device is completely dead or not powering on.

• The phone is stuck on the boot logo, Fastboot, or Recovery Mode.

• You’ve mistakenly flashed the wrong firmware or removed critical partitions.

• You need to repair boot, preloader, lk, or system partitions via ISP.

• IMEI/baseband is unknown due to NVRAM or NVDATA corruption.

⚠️ Caution Before Flashing:

🔐 Always backup your IMEI, NVRAM, and NVDATA before writing the dump.
Flashing the dump file without a security backup may cause IMEI loss, No Service, or Baseband Unknown issues.

✅ Flashing Instructions:

1. Extract the dump file on your PC.

2. Use Pandora Box, Hydra, SP Flash Tool, or any supported Mediatek tool.

3. Select the appropriate MT6781 scatter file.

4. Connect the phone in Preloader/BROM mode (Volume Up + Down, then USB).

5. Write the required partitions or full dump based on your repair need.

6. Reboot the device and verify the recovery.

Optional: After dump flash, you can reflash official Realme firmware using SP Flash Tool for full stability.

📥 Download Link:

🔗 Realme 8i (RMX3151) Scatter Dump File – Free Download (TechFixForum)

read via Easy JTAG Plus, can help revive your device by restoring the original partition structure. Whether your phone is stuck on the logo or showing a black screen, flashing this full dump via UFS programmer can bring it back to working condition.

📱 Device Information:

• Model Name: Vivo Y35

• Model Number: V2205

• Processor (CPU): Qualcomm Snapdragon 680 (SM6225)

• Storage Type: UFS

• Android Version: Android 12 / Funtouch OS (varies by update)

• Boot Mode: Qualcomm EDL 9008 Mode

• Dump Read With: Easy JTAG Plus Box

• File Format: Full UFS Dump (for ISP / socket flashing)

🛠️ Use This Dump File When:

• Device is completely dead or not powering on

• Corrupted partitions due to wrong firmware or update failure

• Stuck in EDL mode, Qualcomm HS-USB QDLoader 9008

• Boot logo hang, recovery stuck, or fastboot issues

• Need to restore complete UFS structure for deep-level repair

⚠️ Important Notice:

💡 Always backup IMEI, EFS, and security partitions (like modemst1, modemst2, fsg) before writing any dump.
Without a backup, you may lose IMEI/network, resulting in No Service or Null IMEI errors.

✅ Flashing Guide:

1. Remove the back panel of the phone and connect the UFS ISP pinout to Easy JTAG Plus.

2. Identify the UFS chip and connect properly using the UFS adapter or socket.

3. Open Easy JTAG software and choose the correct UFS chip.

4. Load the provided dump file.

5. Write full dump or select required partitions.

6. After writing, reassemble the phone and power on.

7. If needed, flash official Vivo firmware via QFIL or QPST to complete the restore.

📥 Download Link:

🔗 Vivo Y35 (V2205) UFS Dump File – Free Download (TechFixForum)

🔗 Stay Connected for More Free Files:

• 🌐 TechFixForum.com – Free Tools, Dumps & Flash Files

This file is especially useful for technicians using EMMC/UFS programmers, or for advanced flashing via boot repair tools like UFI, Easy JTAG, Hydra, or UnlockTool.

📱 Device Info:

• Device Name: Redmi A2+

• Codename: water

• Chipset (CPU): MediaTek Helio G36 (MT6765H)

• Storage Type: eMMC

• Boot Mode: Preloader / BROM Mode

• Tool Used: UnlockTool

• Dump Format: Partition-wise Full Dump

🔧 When to Use This Dump File:

• Device is totally dead (no boot, no recovery).

• Stuck on boot logo or fastboot mode.

• Corrupted or missing partitions such as preloader, lk, boot, vbmeta, system, or userdata.

• Device entered brick state after wrong firmware flash.

• You need to recover partitions via ISP pinout or direct eMMC flashing.

⚠️ Important Note:

Always backup NVRAM, NVDATA, and IMEI partitions before flashing this dump file.
Flashing dump files without security backup may result in IMEI loss, baseband unknown, or no network issues.

✅ Flashing Instructions:

1. Extract the downloaded dump file.

2. Open UnlockTool, UFI, or any other supported tool.

3. Select the proper MT6765/Helio G36 chipset settings.

4. Load and write the required partitions or full dump.

5. Connect the phone in Preloader mode (Volume + and Volume – while inserting USB).

6. Begin the flashing or writing process.

7. After successful flash, reboot the device.

8. If necessary, flash official firmware or restore security backups.

📥 Download Link:

🔗 Redmi A2+ (Water) Full Dump File – Free Download (TechFixForum)

📢 Stay Connected:

Get more tested files, tools, and repair guides free at TechFixForum.com

This backup has been read and extracted using Hydra Tool and is suitable for use in EMMC/ISP flashing or MTK scatter flashing scenarios.

📱 Device Information:

• Model: Vivo Y22

• Model Number: V2207

• Chipset (CPU): MediaTek Helio G85 (MT6769Z)

• Storage Type: eMMC

• Boot Mode: Preloader / BROM Mode

• Dump Format: Scatter-based Partition Dump

• Tool Used: Hydra Tool

• Android Version: Android 12 (may vary)

🔧 Why Use This Dump File?

• Phone completely dead after wrong firmware flash.

• Stuck at Vivo logo, bootloop, or recovery mode.

• Critical partitions like preloader, boot, vbmeta, super, or userdata are corrupted.

• Need full partition restore via ISP pinout or scatter format.

This dump file includes all essential partition images required to revive the phone using Hydra Tool or other tools that support MTK scatter format.

⚠️ Important Warning:

Always try to backup your IMEI, NVRAM, and NVDATA files before flashing.
If you flash this dump without your original security backups, your phone may lose IMEI, resulting in No Network or Baseband Unknown errors.

✅ Flashing Instructions:

1. Extract the downloaded dump package.

2. Launch Hydra Tool or any MTK-supported flashing tool (like SP Flash Tool, UFI, or CM2).

3. Load the MT6769Z_Android_scatter.txt from the extracted folder.

4. Select needed partitions or choose full flashing based on the issue.

5. Boot your device into Preloader mode by holding the volume buttons and connecting USB.

6. Proceed with the flash and wait for completion.

7. After flashing, verify IMEI. If lost, restore via META mode or SN writer.

📥 Download Link:

🔗 Vivo Y22 (V2207) Full Scatter Dump File – Free Download (TechFixForum)

Stay updated with more free dump files, firmware, and tools by joining our repair community at TechFixForum.com

For help, join us on:

this dump will help revive the device to a bootable state.

📱 Device Specifications:

• Model: Infinix Note 7 Lite

• Model Number: X656

• Chipset (CPU): MediaTek Helio P22 (MT6762D)

• CPU Type: Octa-core (4x2.0 GHz Cortex-A53 & 4x1.5 GHz Cortex-A53)

• Storage Type: eMMC

• Boot Mode: Preloader / BROM Mode (MediaTek)

• Flash Format: Scatter File

• Tools Supported: SP Flash Tool, UFI Box, Easy-JTAG (eMMC ISP)

🛠️ When to Use This Dump File?

• Phone is totally dead after a failed flash.

• Device is stuck in boot loop or logo hanging.

• Corrupt or missing partitions like preloader, boot, or system.

• Software malfunction due to wrong firmware or partition overwrite.

• Hardware-level recovery using eMMC ISP pinout or direct eMMC writing.

⚠️ Important Notes Before Flashing:

⚠️ If your device is turning on or partially responding, always backup your IMEI, NVRAM, and NVDATA partitions before flashing this dump.
Flashing this file without a backup may lead to IMEI loss, no network, or baseband unknown.

✅ Flashing Instructions:

1. Download and extract the dump file.

2. Open SP Flash Tool or your preferred box tool (UFI/Easy-JTAG).

3. Load the included MT6762D_Android_scatter.txt file.

4. Select necessary partitions or perform full write.

5. Connect your phone in Preloader mode (hold volume buttons and insert USB).

6. Flash the dump and wait for successful completion.

7. Reboot the device or flash official firmware if needed.

📥 Download Link:

🔗 Infinix Note 7 Lite (X656) Dump File – Free Download (TechFixForum)

This file is free for educational and repair use. Join our Tech Fix Forum to access more tested dump files, firmware, and repair tools. You can also ask questions and share your experiences with our global repair community.

Need help or pinout diagram? Drop a comment on the forum or join our social channels!

professionals needing a full partition restore via UFS ISP or socket method.

📱 Device Specifications:

• Model Name: MOTO G73

• Model Code: XT2237-2

• CPU / Chipset: MediaTek Dimensity 930 (6nm)

• CPU Type: Octa-core (2x2.2 GHz Cortex-A78 & 6x2.0 GHz Cortex-A55)

• GPU: IMG BXM-8-256

• Storage Type: UFS 2.2

• Boot Mode for Flashing: Preloader Mode / BROM Mode (MediaTek)

• Supported Tools: Easy-JTAG Plus, UFI Box (UFS supported)

🛠️ When Should You Use This Dump File?

• Device not booting at all, black screen.

• Stuck in Preloader mode and not detected in SP Flash Tool.

• Flashing wrong firmware or power failure during update caused a brick.

• Need to restore missing or corrupted critical partitions like boot, recovery, vbmeta, super, etc.

• Professional board-level technicians needing ISP-based UFS repair.

⚠️ Important Note Before Flashing:

⚠️ Backup your original IMEI and security partitions (nvram, nvdata, protect1, protect2) if accessible.
Flashing a full dump without these backups may result in IMEI loss, No Network, or Baseband Unknown issues.

✅ Flashing Instructions:

1. Disassemble the phone and locate the UFS ISP pinout (if not using socket adapter).

2. Connect the device to Easy-JTAG, UFI Box, or other UFS programmers.

3. Load and write the required dump partitions or perform a full restore.

4. After writing, reflash the official stock firmware via SP Flash Tool if needed.

5. Test the device for boot and connectivity.

📥 Download Link:

🔗 MOTO G73 (XT2237-2) UFS Dump File – Free Download (TechFixForum)

This UFS Dump is provided for educational and professional use only. If you need help with the UFS pinout or flashing process, visit the community forum at TechFixForum.com

📱 Device Specifications:

• Model Name: Moto G84

• Model Code: XT2347-2

• Software Version: U1TCS34.22-64-19-4-2

• CPU / Chipset: Qualcomm Snapdragon 695 5G (SM6375)

• CPU Type: Octa-core (2x2.2 GHz Kryo 660 Gold & 6x1.7 GHz Kryo 660 Silver)

• GPU: Adreno 619

• Storage Type: UFS 2.2

• RAM Variants: 8GB / 12GB

• Storage Options: 128GB / 256GB

• Boot Mode for Flashing: Qualcomm HS-USB QDLoader 9008 (EDL Mode)

🛠️ When to Use This Dump File:

• Device not powering on at all.

• Phone stuck in EDL (9008) Mode and not responding to fastboot commands.

• Bootloader or system partitions are corrupted or erased.

• No recovery, fastboot, or factory mode access.

• Device bricked during rooting, flashing or custom ROM attempt.

• Hardware repair technicians needing full UFS restore for critical partition repair.

⚠️ Important Warning Before Flashing:

🔴 Always backup IMEI and security partitions such as modemst1, modemst2, fsg, and persist before flashing.
Flashing a full dump without backup can result in IMEI loss, leading to No Network, Null IMEI, or Baseband Unknown errors.

✅ Flashing Guide:

1. Disassemble the device and locate the UFS ISP pinout or use a compatible UFS socket adapter.

2. Connect the device to Easy-JTAG, UFI Box, or other UFS programming tools.

3. Load this Moto G84 dump file into your flashing software.

4. Carefully write the required partitions or perform a full restore depending on damage.

5. Once flashing is complete, reassemble and test the phone.

6. Optionally reflash stock firmware via fastboot for system cleanup.

📥 Download Now:

🔗 Moto G84 XT2347-2 U1TCS34.22-64-19-4-2 Dump File – Free Download (TechFixForum)

This file is shared for professional repair use only. For more tools, tutorials, and technical help, join us at TechFixForum.com

This dump is useful when your device cannot be recovered via fastboot or Rescue and must be restored at the hardware level using UFS programming tools.

📱 Device Hardware Overview:

• Model Name: Moto G85 5G

• Model Code: XT2427-3

• Software Version: U3UO34.49-125-3

• Chipset / CPU: Qualcomm Snapdragon 6s Gen 3 (SM-6375)

• CPU Architecture: Octa-core (2x2.3 GHz & 6x1.8 GHz)

• GPU: Adreno 619

• Storage Type: UFS 2.2

• RAM Options: 8GB / 12GB

• Storage Variants: 128GB / 256GB

• Battery: 5000 mAh, 30W Fast Charging

• Boot Mode for Flashing: Qualcomm HS-USB QDLoader 9008 (EDL Mode)

🛠️ Use Cases for This Dump File:

• The phone is completely dead or stuck in 9008 mode.

• Partition table or UFS firmware is corrupted.

• Bootloader unlock failed, or the flashing process was interrupted.

• Device not booting, no fastboot or recovery mode accessible.

• After short-circuit or voltage spike damaging system partitions.

• You need to restore partitions like abl, devcfg, hyp, boot, system, vendor, persist, modem, etc.

⚠️ Important Note Before Flashing:

📢 Always backup IMEI/security partitions like EFS or modemst1/modemst2 before proceeding.
Flashing dump files without backup may lead to IMEI loss, No Baseband, or Network not working.

✅ Flashing Instructions:

1. Open the phone carefully and locate ISP Pinout or use UFS socket adapter.

2. Connect the device using Easy-JTAG Plus, UFI Box, or similar UFS tool.

3. Load the provided UFS Dump File into the software.

4. Write required or full partitions depending on the damage.

5. Disconnect, reassemble, and test the phone.

6. Reflash official stock ROM via fastboot (if needed) for full software recovery.

📥 Download Link:

🔗 Moto G85 5G (XT2427-3) Dump File – Free Download (TechFixForum)

This dump is for educational and professional repair use only. Always handle UFS repairs with caution, and use reliable tools for flashing.

Need help with UFS pinout, tool drivers, or tutorials? Ask the community at TechFixForum.com

This file is essential for dead boot recovery, UFS repair, and restoring critical partitions using hardware tools like Easy-JTAG Plus, UFI Box, or similar UFS programmers. It has been successfully read and tested from a working Motorola Edge 50 Pro unit.

🔧 Device Hardware Specifications:

• Model Name: Moto Edge 50 Pro

• Code Name: Unknown (update if available)

• Chipset / CPU: Qualcomm Snapdragon 7 Gen 3

• CPU Type: 64-bit Octa-core (1x2.63 GHz + 3x2.4 GHz + 4x1.8 GHz)

• GPU: Adreno 720

• Storage Type: UFS 2.2 / 3.1

• RAM Options: 8GB / 12GB

• Internal Storage: 128GB / 256GB / 512GB

• Battery: 4500 mAh with 125W wired + 50W wireless charging

• Boot Mode for Flashing: Qualcomm EDL Mode (9008)

🛠️ When Should You Use This Dump File?

• Device is completely dead, not responding to power button.

• Stuck in Qualcomm HS-USB QDLoader 9008 mode (EDL).

• After incorrect or interrupted firmware flashing.

• No boot / no recovery / no fastboot access.

• Critical UFS partitions like bootloader, abl, modem, or persist are damaged.

• IMEI and network errors after flashing ROM or rooting.

⚠️ Caution Before Flashing:

🔴 Important: Always try to backup IMEI and security partitions (EFS, modemst1/2, persist) before flashing.
Flashing the dump file without backup could cause IMEI loss, resulting in No Network or Null IMEI.

✅ Flashing Instructions:

1. Open the phone carefully and identify UFS ISP pinout (if available), or use UFS socket adapter.

2. Connect your Easy-JTAG, UFI, or other UFS-supported tool.

3. Load the dump file in the software.

4. Flash required partitions or perform a full UFS dump restore.

5. Recheck with multimeter for shorts before powering ON.

6. Optionally reflash official firmware via fastboot or Rescue Tool for final restore.

📥 Download Now:

🔗 Moto Edge 50 Pro UFS Dump File – Free Download (TechFixForum)

Use this file for professional repair only. This dump is intended for experienced mobile technicians who understand UFS repair processes. For further help, visit TechFixForum.com.